[. . . ] 3-867-106-12(1) Mini Hi-Fi Component System Operating Instructions Owner's Record The model and serial numbers are located on the rear panel. Refer to them whenever you call upon your Sony dealer regarding this product. _______________ MHC-NX1 ©1999 by Sony Corporation 1 WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Press PLAY MODE repeatedly until "PROGRAM" appears in the display. Press one of the DISC 1~5 buttons to select a CD. To programme all the tracks on a CD at once, proceed to step 5. To cancel Programme Play Press PLAY MODE repeatedly until "PROGRAM" or "SHUFFLE" disappears from the display. To Check the programme Clear a track from the end Press CHECK on the remote repeatedly. CLEAR on the remote in stop mode. 4 Turn the jog dial until the desired track appears in the display. Disc number 3 Clear a specific CHECK on the remote track repeatedly until the number of the track to be erased lights up, then press CLEAR. Add a track to 1 Select the disc tray with a the programme DISC 1~5 button. Clear the entire once in stop mode or twice programme while playing. PROGRAM Track number 5 Press ENTER. The track is programmed. The last programmed track and the total programmed track number appear, followed by the total playing time. Total playing time Tips · The programme you made remains in the CD player even after it has been played back. · If "--. --" appears instead of the total playing time during programming, this means: ­ you have programmed a track number which exceeds 20 ­ the total playing time has exceeded 100 minutes. PROGRAM The last programmed track 6 To programme additional tracks, repeat steps 3 to 5. Press ·. All the tracks play in the order you selected. 7 21 The Tape Deck Recording on a tape manually You can record from CD, tape, or radio as you like. For example, you can record just the songs you want or record from the middle of the tape. The recording level is adjusted automatically. 1/u (power) 4 Press DIRECTION repeatedly to select A to record on one side. Press REC PAUSE/START. Recording starts. 5 6 2 Start playing the source to be recorded. To Stop recording Press on the deck B Pause recording REC PAUSE/START + ) ­ 0 Tips + ­ + g § 1 2 · 3 4 5 · If you want to record from the reverse side, press ª so that ª (for reverse side) lights up. · When you want to reduce the hiss noise in lowlevel high-frequency signals, press DOLBY NR so that "DOLBY NR" lights up after pressing REC PAUSE/START in step 3. · When recording from a CD, you can use the jog dial to select tracks during recording pause mode (after pressing REC PAUSE/START in step 3 and before pressing again in step 5). ª · ª · Note Dolby NR is off and DIRECTION (A or RELAY) is ß when the mains AC power supply is switched off. § § 4 1 2 3 ª 3, 5 DOLBY NR 1 Insert a recordable tape into deck B. · (for front side) lights up. 22 Recording a CD by specifying track order -- Programme Edit You can record tracks from all the CDs in the order you want. When programming, make sure the playing times for each side do not exceed the length of one side of the tape. 1/u (power) 1 2 3 4 5 Place a CD and insert a recordable tape into deck B. Press PLAY MODE repeatedly until "PROGRAM" appears in the display. Turn the jog dial until the desired track appears in the display. Disc number 3 5 EDIT 32 6 ­ 0 + ) PROGRAM + ­ + Track number g 6 § 1 2 Press ENTER. The track is programmed. The last programmed track and the total programmed track number appear, followed by the total playing time. Total playing time · 3 4 5 ª · ª · PROGRAM The last programmed track § § 7 8 11 DOLBY NR 10 4 1 12 To programme additional tracks to be recorded on side A, repeat steps 4 to 6. Skip step 4 to select tracks from the same disc. continued 23 Recording a CD by specifying track order (continued) Selecting tape length automatically -- Tape Select Edit You can check the most suitable tape length for recording a CD. Note that you cannot use Tape Select Edit for discs containing more than 20 tracks. 8 Press (P on the remote) to insert a pause at the end of side A. "P" appears in the display and the total playing time resets to "0. 00" in the display. 9 Repeat steps 5 and 6 for tracks from the same disc or steps 4 to 6 for tracks from another disc to programme the remaining tracks to be recorded on side B. 1 2 3 Insert a CD. Press EDIT (EDIT/PTY on European model) once so that "EDIT" flashes. The required tape length for the currently selected CD appears, followed by the total playing time for side A and side B respectively. 10 Press CD SYNC. Deck B stands by for recording and the CD player stands by for playback. · (for front side) lights up. 11 Press DIRECTION repeatedly to select A to record on one side. Select ß (or RELAY) to record on both sides. Notes · You cannot use this function after programming. [. . . ] ·The remote is not pointing in the direction of the system's sensor. ·Move the microphone away from the speakers or change the direction of the microphone. ·Turn off the TV set once, then turn it on after 15 to 30 minutes. If the colour irregularity still persists, place the speaker farther away from TV set. [. . . ]